재고 있음 인기 제품
LCM-60KN
LCM-60KN MEANWELL AC-DC Multi-Stage LED driver Constant Current (CC), Modular output 0.5A/0.6A/0.7A/0.9A/1.0..
$0.00USD
3188개 재고
주요 사양
이름 (상세 정보):LCM-60KN
전력(세부 정보):60,3 W
상태 (세부 정보):New
재고 (상세 정보):Yes
공급업체 정보
MEANWELL
제품: 6448
보통 2-3 영업일 내에 발송됩니다
품질 보장
빠른 배송
기술 지원
기술 사양
| 매개변수 | 가치 |
|---|---|
| 이름 (상세 정보) | LCM-60KN |
| 전력(세부 정보) | 60,3 W |
| 상태 (세부 정보) | New |
| 재고 (상세 정보) | Yes |
| 형식 (세부 정보) | Box |
| 시리즈 (상세 정보) | LCM-60KN |
| 승인 내역 (상세 정보) | CCC, CE, EAC, ENEC, MM |
| 전력(와트) (상세 정보) | 60,30 |
| 규정 (세부 사항) | KNX |
| 세부정보 (Subformato) | IP20 |
| 너비(mm) (상세 정보) | 81.50 |
| 높이(mm) (상세 정보) | 23.00 |
| AC 입력 최대값 (상세 정보) | 295,00 |
| AC 입력 최소값 (상세 정보) | 180,00 |
| 지원서 (상세 정보) | Lighting |
| 제조업체 (상세 정보) | MEAN WELL |
| 제품 유형 (상세 정보) | LED Driver |
| 격리(V) (세부 사항) | 3.750,00 |
| 출력 전류 (상세 정보) | 500mA |
| 최대 출력(와트) (상세 정보) | 60.3 |
| 입력 커넥터(세부 정보) | Quick Connector |
| 입력 주파수 (상세 정보) | 50 Hz, 60 Hz |
| 장문/배경 (세부 정보) | 123.50 |
| 상세 설명 (세부 정보) | LED driver dimmable by signal KNX and a push button.Specially designed for powering LEDs directly in a steady stream.Format in plastic boxIP20.Input range180-295Vca47-63Hz.Current output selectable by micro-switch500, 600, 700, 900, 1050 or 1400mA.Output current500mA600mA700mA900mA1050mA1400mAPower60,3 W60,3 W60,3 W60,3 W60,3 W60,3 WRange of Output Voltage2-90Vcc2-90Vcc2-86Vcc2-67Vcc2-57Vcc2-42VccEfficiency typical:91%.Regulationsignal-KNX and a push button.Functions: dimming, manual, hours of operation, and feedback of energy consumption.Synchronization: we can sync up10 unitsvia the wires LCM-xxx-SYNC in such a way that by regulating a source other do the same regulation.Input class II without grounding.Factor corrector, power>0,975to 230vac at full load.Linear curve or a logarithmic programmableinterfacepush button KNXintegrated.Supportemergency lighting(THE).Possibility of programmingCLO (Constant Light Output).Operating temperature range of caseTcfrom-30ºCup+90ºC.Dimensions (Length x Width x Height):123,5 x to 81.5 x 23mm.3 years of warranty.Manufacturer: MEAN WELL.VIDEO LCM-40KN - FIRST LED DRIVER MULTICORRIENTE KNX.This source is designed to work directly with leds (plates LED or COBs), not with LED strips. Must be equipment that is fed in a steady stream.This source works on a constant Current when we connect the LEDs directly to have a voltage within the range of rensión output mode constant current and a working current equal to the output current.Be sure to adjust the output current desired using the selector outlet.For more information please see the datasheet in the section attachments.This version (KN) is governed by the protocolKNX. With multiple levels selectable through DIP switch and the KNX interface. We can regulate directly by KNX without the need of the typical gateway KNX-DALI. The input range is 180-295Vca and offers different levels of power, varying between 500-1400mA.These drivers have a high efficiency (91%) and a fanless design, being able to work at temperatures (of the box) between -30 ° C and +90 ° C. in Addition, we have the ability to schedule the CLO (Constant Light Output), which increases with the hours of operation, the output current, to always maintain the same brightness and save energy, while increasing the life of the leds.With plastic housing, designed for applications of LED lighting. Suitable for indoor lighting, modern constructions and intelligent or buildings-houses refurbished for not rewiring, stairs (with two buttons on the same switch) and outdoor applications.Low ripple current, no flicker (flicker-free).Input for protection by temperature of the LED modules. The driver has an input to connect a NTC sensor (resistance of a negative coefficient) which allows us to reduce the output current in case of excess of temperature in the LED modules. If we're not going to use this input protection, we can use it to connect a fixed resistor and adjust the output current to values lower intermediate up to 56% lower than the value selected with the DIP-Switch. For example if we want a current of 630mA we can adjust the output with the jumpers to 700mA and connect a resistor of 34kOhmnios. For more information please see the datasheet in the tab "Attachments" and you can use the Excel file to calculate the value of the resistance.Some of the sensors supported are:MEAN WELL: WPD-06SWT Push button dual wireless, without batteries.MEAN WELL: NWC-300 programmer EnOcean USB for the configuration of the system.MEAN WELL: EOSWA-W-EO sensor of presence of a wall.MEAN WELL: EOSCA-W-EO sensor of presence of roof.MEAN WELL: ELLSU-W-EO brightness sensor. |
| 출력 커넥터(세부 정보) | Quick Connector |
| 입력 유형 CA (세부 정보) | Single-phase |
| 보증 기간(년) (상세 정보) | 3,00 |
| 원산지 (상세 정보) | China |
| 출력 전류(mA) (상세 정보) | 500, 550, 600, 650, 700, 750, 800, 850, 900, 950, 1000, 1050, 1100, 1150, 1200, 1250, 1300, 1350, 1400 |
| 전력 (추가 정보) | 60,3 W |
| 출력 전압 범위 (상세 정보) | 2-90Vcc |
| 출력 전류 (추가 정보) | 500mA |
| 최소 출력 강도(mA) (상세 정보) | 500,00 |
| 최대 출력 강도(mA) (상세 정보) | 1.400,00 |
| 출력 전압 범위 (추가 정보) | 2-90Vcc |
제품 설명
More details
주요 기능
- 산업 등급 품질
- RoHS 준수
- CE 인증
- 1년 보증
기술 세부 정보
LED driver dimmable by signal KNX and a push button.
제품 문서
데이터시트
기술 사양 및 성능 데이터
사용자 매뉴얼
설치 및 운영 가이드
