재고 있음 인기 제품
ULS501P
ULS501P LS-501P PANASONIC Laser Amplifier (with display), connector type, 2 outputs PNP
$0.00USD
3330개 재고
주요 사양
목:Specifications
케이블:-
무게:Net weight: 15 g approx.Gross weight: 55 g approx.
세부:Amplifiers(Connector type)
공급업체 정보
PANASONIC
제품: 4316
보통 2-3 영업일 내에 발송됩니다
품질 보장
빠른 배송
기술 지원
기술 사양
| 매개변수 | 가치 |
|---|---|
| 목 | Specifications |
| 케이블 | - |
| 무게 | Net weight: 15 g approx.Gross weight: 55 g approx. |
| 세부 | Amplifiers(Connector type) |
| 제품 | Amplifier-separated Type Digital Laser Sensor |
| 재료 | Enclosure: PolycarbonateCover: PolycarbonateSwitch: Polyacetal |
| 종범 | FX-MB1 (Amplifier protective seal): 1 set |
| 보호 | IP40(IEC) |
| 부품 번호 | LS-501P |
| 제품명 | Amplifier-separated Type Digital Laser Sensor LS-500 |
| 응답 시간 | H-SP: 60 micro s or less, FAST: 150 micro s or less, STD: 250 micro s or less, LONG: 500 micro s or less, U-LG: 5 ms or less, HYPR: 24 ms or less selectable |
| 외부 입력 | PNP non-contact input- Signal condition High: +4 Vto+V DC(sink current 3.0 mA or less), Low: 0 to +0.6 V DC or open- Input impedance: 10 kOhm approx.(Note：Select either sensing output 2 or external input.) |
| 제품 번호 | LS-501P |
| 공급 전압 | 12 to 24 V DC +10-15% Ripple P-P 10 % or less |
| 타이머 기능 | OFF-delay timer, ON-delay timer, ONE-SHOT timer, ON / OFF-delay timer, ON-delay / ONE-SHOT timer,switchable either effective of ineffective, with variable timer periodOFF-delay timer, ON-delay timer, ONE-SHOT timer,switchable either effective of ineffective, with variable timer period |
| 연장 케이블 | Extension up to total 100 m 328.084 ft is possible with 0.3mm2, or more, cable. |
| 디지털 디스플레이 | 8-digit 7-segment digital display (4-digit green LED + 4-digit red LED), MODE indicator (Yellow LED): L/D, CUST, PRO |
| 주변 습도 | 35 to 85 % RH, Storage: 35 to 85 % RH |
| 충격 저항 | 98 m/s2acceleration (10 G approx.) in X, Y and Z directions for five times each |
| 논리 연산 | Between sensing output 1 and calculation target: Disabled / and / or / xor, selectableCalculation target: Sensing output 2 / adjacent upstream amplifier (sensing output 1) / external input, selectable |
| 전력 소비량 | Normal operation: 1,200 mW or less (Current consumption 50 mA or less at 24 V supply voltage)ECO mode: 980 mW or less (Current consumption 40 mA or less at 24 V supply voltage) |
| 주변 온도 | -10 to +55degrees + 14 to 131 degrees Fahrenheit (If 4 to 7 units are mounted close together, -10 to +50 degrees +14 to +122 degrees Fahrenheit ; if 8 to 16 units are mounted close together, -10 to +45 degrees +14 to +113 degrees Fahrenheit )(No dew condensation or icing allowed), Storage: -20 to +70 degrees -4 to +158 degrees Fahrenheit |
| 작동 표시기 | Orange LED (lights up when sensing output 1 or sensing output 2 is ON) |
| 감도 설정 | 2-level teaching / limit teaching / full auto teaching / manual adjustment |
| 타이머 기능: 시간 | Timer range '' ms'': 0.5 ms approx., 1 to 9,999 ms approx., in approx. 1 ms intervalsTimer range '' sec'': 0.5 sec. approx., 1 to 32 sec. approx., in approx. 1 sec. intervalsTimer range '' 1/10 ms'': 0.05 ms approx., 0.1 to 999.9 ms approx., in approx. 0.1 ms intervals, Set separately for each output. |
| 진동 저항 | 10 to 150 Hz frequency, 1.5 mm double amplitude or maximum acceleration 98 m/s2in X, Y, and Z direction for 2 hours each. |
| 절연 저항 | 20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure |
| 규정 준수 | EMC Directive, RoHS Directive |
| 현재 출력을 모니터링합니다. | - |
| 외부 입력 기능 | Laser emission halt / teaching (full-auto teaching, limit teaching, 2 point teaching) / logic operation setting / copy lock /display adjustment / data bank load / data bank save, selectable |
| 출력 선택 표시기 | Yellow LED (lights up when output is selected) |
| 레이저 방출 표시기 | Green LED (lights up during laser emission) |
| 전압 내성 | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
| 입사광 표시 범위 | H-SP/FAST/STD: 0 to 4,000LONG/U-LG/HYPR: 0 to 9,999 |
| 감지 출력 (감지 출력 1, 2) | PNP open-collector transistor・Maximum source current: 50 mA (Note：25 mA if 5 or more amplifier are connected in cascade (excluding cable extension).)・Applied voltage: 30 V DC or less (between output and +V)・Residual voltage: 2 V or less (at max. source current)(Note：Select either sensing output 2 or external input as the connector type.) |
| 감지 출력 설정: 감지 출력 1 | Normal mode, differential mode, hysteresis mode, window comparator mode, selectable |
| 감지 출력 설정: 감지 출력 2 | Normal mode, differential mode, hysteresis mode, self-diagnostic output mode, selectable(Note：Select either sensing output 2 or external input.) |
| 자동 간섭 방지 기능 | Incorporated(Note：Number of units that can be mounted close together: 0 for H-SP; 2 for FAST; 4 for STD, LONG, U-LG, or HYPR) |
| 감지 출력(감지 출력 1, 2):출력 작동 | Selectable either Light-ON or Dark-ON |
| 감지 출력(감지 출력 1, 2): 단락 보호 | Incorporated |
제품 설명
LS500. Laser Amplifier (with display), connector, 2 PNP outputs
주요 기능
- 산업 등급 품질
- RoHS 준수
- CE 인증
- 1년 보증
제품 문서
데이터시트
기술 사양 및 성능 데이터
사용자 매뉴얼
설치 및 운영 가이드
