재고 있음 인기 제품
USFC21
USFC21 SF-C21 PANASONIC Safety control unit for safety light curtain and other safety products, 8 inputs 24V..
$0.00USD
4642개 재고
주요 사양
목:Specifications
무게:Net weight: 190 g approx.Gross weight: 320 g approx.
제품:Safety Control Unit
재료:Main unit enclosure: Polycarbonate / ABS polymer alloyEnclosure: Polycarbonate
공급업체 정보
PANASONIC
제품: 4316
보통 2-3 영업일 내에 발송됩니다
품질 보장
빠른 배송
기술 지원
기술 사양
| 매개변수 | 가치 |
|---|---|
| 목 | Specifications |
| 무게 | Net weight: 190 g approx.Gross weight: 320 g approx. |
| 제품 | Safety Control Unit |
| 재료 | Main unit enclosure: Polycarbonate / ABS polymer alloyEnclosure: Polycarbonate |
| PFHD/ MTTFD | 9.73 x 10−10/ 100 years or more |
| 부품 번호 | SF-C21 |
| 케이블 길이 | 100 m328.084 ftor less |
| 제품명 | Safety Control Unit SF-C21 |
| 제품 번호 | SF-C21 |
| 오염도 | 2 |
| 연결 방식 | Input / output and power supply: Detachable spring cage termina l blocksRS-485: Detachable spring-cage terminal blockUSB: Mini-B male |
| 관련 표준 | IEC 60947-1, IEC 60947-5-1, IEC 60947-5-2, IEC 60947-5-5, IEC 60947-5-8, IEC 61496-1, IEC TS 62046, ISO 13851 |
| 인터록 기능 | Incorporated |
| 작동 고도 | 2,000 m6561.680 ftor less(Note) Do not use or store this device in a pressurized environment beyond the atmospheric pressure at sea level. |
| 진동 저항 | 5 to 8.4 Hz frequency, 3.5 mm0.138 inhalf amplitude, 8.4 to 150 Hz frequency, Max. acceleration 9.8 m/s2(1 G), in X, Y and Z directions for two hours each (IEC / EN 60068-2-6) |
| 논리 설정 기능 | Input mode, control mode, output mode, reset mode, auxiliary ou tput mode |
| 과전압 범주 | II |
| 음소거 표시기 출력 | Semiconductor photo MOS relay output x 1- Maximum load current: 60 mA- Supply voltage: Same as the voltage of the power supply for internal- Residual voltage: 2.5 V or less- Leakage current: 100 μA or less (Including power supply OFF condition) |
| 잠금 해제 기능 | Incorporated |
| 논리 선택 기능 | No.0: Customization controlNo.1: Overall stop controlNo.2: Parallel muting controlNo.3: Sequential muting controlNo.4: Partial stop control 1No.5: Partial stop control 2No.6: Two-hand controlNo.7: OR controlNo.8: Operation mode selection control |
| 안전 입력(IN1~IN8) | 2 inputs x 4, Rated voltage: Same as the voltage of the power supply for internal |
| 적용 표준: EMC | IEC 61000-6-2, IEC 61326-3-1, EN 55011 |
| 전원을 켠 후 시작 시간 | 2 sec. or less |
| 적용 기준: 안전 | IEC 61508-1 to 3, EN 61508-1 to 3 (SIL3), ISO 13849-1:2015 (Category 4, PLe), IEC 61131-2, IEC 61010-2-201, IEC 62061 (SILCL3), UL 61010-1, UL 61010-2-201, UL 1998 |
| 제어 출력(OUT1 ~ OUT4) | PNP open-collector transistor with 2 outputs x 2- Maximum source current: 300 mA / output- Applied voltage: Same as the voltage of the power supply for external- Residual voltage: 2.5 V or less- Leakage current: 100 μA or less (Including power supply OFF condition) |
| 통신 기능(MODBUS RTU) | Interface: RS-485Protocol: MODBUS RTUMaximum transmission distance: 100 m328.084 ftMaximum number of units that can be connected: 8 units (slaves) |
| 외부 장치 모니터링 기능 | Incorporated |
| 안전 입력(IN1~IN8): 켜짐 수준 | Input voltage: 18 VInput current: 3.5 mA |
| 음소거 표시기 출력: 출력 모드 | ON when muting / override |
| 안전 입력(IN1~IN8): OFF 레벨 | Input voltage: 5 VInput current: 1.0 mA |
| 음소거 표시기 출력: 응답 시간 | 10 ms or less |
| 적용 가능한 규정 및 인증 | CE Marking (Machinery Directive, EMC Directive, RoHS Directive), UKCA Marking [Supply of Machinery (Safety)Regulations, EMC Regulations, RoHS Regulations], TÜV SÜD certification, Korea's Radio Waves Act conformity registration |
| 환경 저항성: 주변 습도 | 30 to 85 % RH, Storage: 30 to 85 % RH |
| 환경 저항성: 충격 저항성 | 147 m/s2(15 G) 11 ms in X, Y and Z directions for three times each (IEC / EN 60068-2-27) |
| 공급 전압: 외부 전원 공급 장치 | 24 V DC+10-15% Ripple P-P10 % or less(Note) "Power supply for external" is the power supply for control output / auxiliary output. The power supplies for internal and external are insulated.(Note) The power supply unit connected to this device must satisfy the conditions below.- Output voltage within 20.4 V to 26.4 V DC (Ripple P-P: 10 % or less.)- Power supply unit SELV (safety extra low voltage) / PELV (protected extra low voltage) conforming to the EMC Directive and Low-voltage Directive (In case CE Marking conformity is required.)- Power supply unit conforming to the Low-voltage Directive and with an output of 100 VA or less- Power supply unit SELV (safety extra low voltage) / PELV (protected extra low voltage) conforming to the EMC Regulations and Low-voltage Regulations (In case UKCA Marking conformity is required.)- Power supply unit with an output holding time of 20 ms or more.- Power supply unit corresponding to CLASS 2 (In case C-TÜV US Listing Mark conformity is required.) |
| 공급 전압: 내부 전원 공급 장치 | 24 V DC+10-15% Ripple P-P10 % or less(Note) "Power supply for internal" is the power supply for safety input. The power supplies for internal and external are insulated.(Note) The power supply unit connected to this device must satisfy the conditions below.- Output voltage within 20.4 V to 26.4 V DC (Ripple P-P: 10 % or less.)- Power supply unit SELV (safety extra low voltage) / PELV (protected extra low voltage) conforming to the EMC Directive and Low-voltage Directive (In case CE Marking conformity is required.)- Power supply unit conforming to the Low-voltage Directive and with an output of 100 VA or less- Power supply unit SELV (safety extra low voltage) / PELV (protected extra low voltage) conforming to the EMC Regulations and Low-voltage Regulations (In case UKCA Marking conformity is required.)- Power supply unit with an output holding time of 20 ms or more.- Power supply unit corresponding to CLASS 2 (In case C-TÜV US Listing Mark conformity is required.) |
| 제어 출력(OUT1~OUT4): 출력 모드 | True: ONFalse: OFF |
| 안전 입력(IN1~IN8): 입력 임피던스 | 4.7 KΩ approx. |
| 환경 저항성: 주변 온도 | -10 to +55 ℃+14 to +131 ℉(No dew condensation or icing allowed), Storage: -25 to +60 ℃-13 to +140 ℉ |
| 제어 출력(OUT1~OUT4): 응답 시간 | OFF response: 10 ms or lessON response: 100 ms or less |
| 환경 저항성: 보호 정도 | IP20 (IEC)(must be installed in a control panel with protectio n IP54 or higher) |
| 환경 저항성: 절연 저항 | 20 MΩ, or more, with 500 V DC megger(All inputs connected together - USB port, all inputs connected together - RS-485 port, USB port - RS-485 port, between all supply terminals connected together and enclosure, all outputs connected together - all input connected together, all outputs connected together - USB port, all outputs connected together - RS-485 port) |
| 소비 전류: 외부 전원 공급 장치 | 100 mA or less(Note) "Power supply for external" is the power supply for control output / auxiliary output. The power supplies for internal and external are insulated.(Note) The power supply unit connected to this device must satisfy the conditions below.- Output voltage within 20.4 V to 26.4 V DC (Ripple P-P: 10 % or less.)- Power supply unit SELV (safety extra low voltage) / PELV (protected extra low voltage) conforming to the EMC Directive and Low-voltage Directive (In case CE Marking conformity is required.)- Power supply unit conforming to the Low-voltage Directive and with an output of 100 VA or less- Power supply unit SELV (safety extra low voltage) / PELV (protected extra low voltage) conforming to the EMC Regulations and Low-voltage Regulations (In case UKCA Marking conformity is required.)- Power supply unit with an output holding time of 20 ms or more.- Power supply unit corresponding to CLASS 2 (In case C-TÜV US Listing Mark conformity is required.) |
| 소비 전류: 내부 전원 공급 | 200 mA or less(Note) "Power supply for internal" is the power supply for safety input. The power supplies for internal and external are insulated.(Note) The power supply unit connected to this device must satisfy the conditions below.- Output voltage within 20.4 V to 26.4 V DC (Ripple P-P: 10 % or less.)- Power supply unit SELV (safety extra low voltage) / PELV (protected extra low voltage) conforming to the EMC Directive and Low-voltage Directive (In case CE Marking conformity is required.)- Power supply unit conforming to the Low-voltage Directive and with an output of 100 VA or less- Power supply unit SELV (safety extra low voltage) / PELV (protected extra low voltage) conforming to the EMC Regulations and Low-voltage Regulations (In case UKCA Marking conformity is required.)- Power supply unit with an output holding time of 20 ms or more.- Power supply unit corresponding to CLASS 2 (In case C-TÜV US Listing Mark conformity is required.) |
| 안전 입력(IN1~IN8): 정격 입력 전류 | 5 mA approx. |
| 보조 출력(AUX1~AUX4)(비안전 출력) | PNP open-collector transistor with 1 output x 4- Maximum source current: 60 mA / output- Applied voltage: Same as the voltage of the power supply for external- Residual voltage: 2.5 V or less- Leakage current: 100 μA or less (Including power supply OFF condition) |
| 제어 출력(OUT1~OUT4): ON 지연 기능 | Incorporated |
| 환경 저항성: 전압 내성 | 1,000 V AC for one min.(All inputs connected together - USB port, all inputs connected together - RS-485 port, USB port - RS-485 port, between all supply terminals connected together and enclosure, all outputs connected together - all input connected together, all outputs connected together - USB port, all outputs connected together - RS-485 port) |
| 제어 출력(OUT1~OUT4): OFF 지연 기능 | Incorporated |
| 음소거 표시기 출력: 단락 보호 | Incorporated |
| 제어 출력(OUT1~OUT4): 단락 보호 | Incorporated |
| 안전 입력(IN1~IN8): 감지 가능한 ON 상태 지속 시간 | 10 ms or more |
| 안전 입력(IN1~IN8): 감지 불가능한 OFF 상태 지속 시간 | 0.7 ms or less |
| 보조 출력(AUX1~AUX4)(비안전 출력): 응답 시간 | 10 ms or less |
| 보조 출력(AUX1~AUX4)(비안전 출력): 단락 보호 | Incorporated |
| 보조 출력(AUX1~AUX4)(비안전 출력): 출력 모드(공장 기본 설정) | AUX1: Negative logic of OUT1 / OUT2 (ON when OUT1 / OUT2 is OFF)AUX2: Negative logic of OUT3 / OUT4 (ON when OUT3 / OUT4 is OFF)AUX3: Reset trigger output (ON under reset release wait condition)AUX4: Lockout output (OFF when lockout) |
| 보조 출력(AUX1~AUX4)(비안전 출력): 출력 모드 (소프트웨어 도구를 사용하여 모든 보조 출력을 사용자 지정할 수 있습니다.) | Negative logic of OUT1 / OUT2 (ON when OUT1 / OUT2 is OFF)Negative logic of OUT3 / OUT4 (ON when OUT3 / OUT4 is OFF)Positive logic of OUT1 / OUT2 (ON when OUT1 / OUT2 is ON)Positive logic of OUT3 / OUT4 (ON when OUT3 / OUT4 is ON)Outputs A, B, C, and D of diagnosis results of input blocks (ON when logic is true)Outputs E, F, and G of internal logic circuit diagnostic results (ON when logic is true)Reset trigger output (ON under reset release wait condition)Lockout output (OFF when lockout)Muting indicator output (ON when muting / override)Monitor output in response to IN1 to IN8 (ON when input)No output (normally OFF) |
제품 설명
Control unit for barriers and other safety products, Cat. 4(Ple) and SIL3, 4 inputs, 2 outputs, 8 pre-established logics according to cat regulations. 4 (Ple) and 1 customizable logic, self-diagnostic
주요 기능
- 산업 등급 품질
- RoHS 준수
- CE 인증
- 1년 보증
제품 문서
데이터시트
기술 사양 및 성능 데이터
사용자 매뉴얼
설치 및 운영 가이드
