재고 있음 인기 제품
UST4C11
UST4C11 ST4-C11 PANASONIC Controller for ST4
$0.00USD
3452개 재고
주요 사양
목:Specifications
PFHD:Refer to the following table(Note： (Probability of dangerous failure per hour) depends on number of single beam sensorST4-A□connected to controller.)
MTTFD:More than 100 years (Note：Mean time to dangerous failure (in years))
무게:Net weight: 180 g approxGross weight: 390 g approx
공급업체 정보
PANASONIC
제품: 4316
보통 2-3 영업일 내에 발송됩니다
품질 보장
빠른 배송
기술 지원
기술 사양
| 매개변수 | 가치 |
|---|---|
| 목 | Specifications |
| PFHD | Refer to the following table(Note： (Probability of dangerous failure per hour) depends on number of single beam sensorST4-A□connected to controller.) |
| MTTFD | More than 100 years (Note：Mean time to dangerous failure (in years)) |
| 무게 | Net weight: 180 g approxGross weight: 390 g approx |
| 세부 | Controller |
| 제품 | Compact Type 4 Safety Beam Sensor |
| 재료 | Enclosure: ABS |
| 부품 번호 | ST4-C11 |
| 제품명 | Compact Type 4 Safety Beam Sensor ST4 |
| 배선 케이블 | Terminal block connector: 0.2 to 1.5 mm2 |
| 전력 전압 | 24 V DC +10-15 % Ripple P-P 10 % or less |
| 응답 시간 | OFF response: 25 ms or lessON response: 90 ms or less (auto reset) / 140 ms or less (manual reset) |
| 제품 번호 | ST4-C11 |
| 보조 출력 | PNP open-collector transistor / NPN open-collector transistor (Set using output polarity selection switch)ST4-C11: one outputST4-C12EX: four outputs[PNP output]Maximum source current: 100 mAApplied voltage: same as the supply voltage (between auxiliary output and +V)Residual voltage: 2.5 V or less (at 100 mA source current)[NPN output]Maximum sink current: 100 mAApplied voltage: same as the supply voltage (between auxiliary output and 0 V)Residual voltage: 2.0 V or less (at 100 mA sink current)(Note) If the total current of the control outputs (OSSD1, OSSD2), auxiliary outputs, and muting lamp output exceeds 400 mA, the wiring resistance between the controller and the power supply should be 1 Ohm or less. In addition, if the total current is 400 mA or less, the wiring resistance between the controller and the power supply should be 2 Ohm or less. |
| 램프 출력 음소거 | -(Note) If the total current of the control outputs (OSSD1, OSSD2), auxiliary outputs, and muting lamp output exceeds 400 mA, the wiring resistance between the controller and the power supply should be 1 Ohm or less. In addition, if the total current is 400 mA or less, the wiring resistance between the controller and the power supply should be 2 Ohm or less. |
| 연결 단말기 | Detachable spring-cage terminal |
| 현재 소비량 | 100 mA or less (excluding sensor head ST4-Ax) |
| 적용 가능한 표준 | IEC 61496-1/2 (JIS B 9704-1/2 / UL 61496-1/2) (Type 4), ISO 13849-1:2015 (Category 4, PLe), JIS B 9705-1 (Category 4), IEC 61508-1 to 3 (SIL3), IEC 62061 (SIL3), JIS C 0508-1 to 3 (SIL3), UL 1998, OSHA 1910.212, OSHA 1910.217 (C), ANSI B11.1 to B11.19, ANSI/RIA R15.06, ANSI/ISA S84.01 (SIL3)(Note) Complies with those standards only when the controller is used in combination with the sensor head ST4-x. |
| 적용 가능한 센서 헤드 | ST4-Ax |
| CE 마크 지침 준수 | Machinery Directive, EMC Directive, RoHS Directive |
| 보조 출력: 작동 모드 | OFF when all beams of the connected ST4-Axs are receivedON when one or more beams of the connected ST4-Axs are interrupted |
| 제어 출력(OSSD 1, OSSD 2) | PNP open-collector transistor / NPN open-collector transistor Dual output x 1 system (Set using output polarity selection switch)[PNP output]Maximum source current: 200 mAApplied voltage: same as the supply voltage (between control output and +V)Residual voltage: 2.5 V or less (at 200 mA source current)Leakage current: 200 micro A or less (including power OFF condition)Maximum load capacity: 1 micro F (from no-load to max. source current)Load wiring resistance: 3 Ohm or less (between control output and load)[NPN output]Maximum sink current: 200 mAApplied voltage: same as the supply voltage (between control output and 0 V)Residual voltage: 2.0 V or less (at 200 mA sink current)Leakage current: 200 micro A or less (including power OFF condition)Maximum load capacity: 1 micro F (from no-load to max. sink current)Load wiring resistance: 3 Ohm or less (between control output and load)(Note) If the total current of the control outputs (OSSD1, OSSD2), auxiliary outputs, and muting lamp output exceeds 400 mA, the wiring resistance between the controller and the power supply should be 1 Ohm or less. In addition, if the total current is 400 mA or less, the wiring resistance between the controller and the power supply should be 2 Ohm or less. |
| 보조 출력: 보호 회로 | Incorporated |
| 램프 출력 음소거: 보호 회로 | Incorporated |
| 환경 저항성: 주변 습도 | 30 to 85 % RH, Storage: 30 to 95 % RH |
| 환경 저항성: 충격 저항성 | 300 m/s2acceleration in X, Y and Z directions three times each |
| 환경 저항성: 주변 온도 | －10 to +55 ℃+14 to +131℉(No dew condensation or icing allowed),Storage: －25 to +70 ℃－13 to +158℉ |
| 환경 저항성: 보호 정도 | Enclosure: IP40 (IEC)Terminal: IP20 (IEC) |
| 환경 저항성: 진동 저항성 | 10 to 55 Hz frequency, 0.75 mm0.030 indouble amplitude or maximum acceleration 90 m/s2 in X, Y and Z directions for two hours each< |
| 환경 저항성: 절연 저항 | 20 MOhm or more with 500 V DC mega between all supply terminals connected together and enclosure |
| 제어 출력(OSSD 1, OSSD 2): 작동 모드 | ON when all beams of the connected ST4-Axs are receivedOFF when one or more beams of the connected ST4-Axs are interruptedOFF during lockout |
| 적용 가능한 센서 헤드: 직렬 연결 수 | Interference prevention possible when up to a maximum of 6 sets are connected(When the maximum of 3 controllers are connected together, interference prevention is possible for up to 18 sets) |
| 제어 출력(OSSD1, OSSD2): 보호 회로 | Incorporated |
| 환경 저항성: 전압 내성 | 1,000 V AC for one min. between all supply terminals connected together and enclosure |
제품 설명
Standard Control Unit Safety Barrier Category 4 Ple SIL 3, ST4 Series
주요 기능
- 산업 등급 품질
- RoHS 준수
- CE 인증
- 1년 보증
제품 문서
데이터시트
기술 사양 및 성능 데이터
사용자 매뉴얼
설치 및 운영 가이드
